 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TECHNICAL DATA Dual Operational Amplifiers IL4558 The IL4558 is dual general purpose operational amplifiers. The high common-mode input voltage range and the absence of latch-up make these amplifiers ideal for voltage follower application. The devices are short circuit protected and the internal frequency Compensation ensures stability without external components. FEATURE * * * * * * * * Short Circuit Protection Wide common-mode and differential ranges No frequency compensation required Low power consumption No latch-up 3 MHz unity gain bandwidth guaranteed Gain and phase match between amplifiers Possible to exchange the position of Pin9 for Pin1 because of Pin Connection being symmetric(IL4558S only) ORDERING INFORMATION IL4558N Plastic IL4558D SOIC IL4558S-9 SIP-9 IL4558S SIP-8 TA = -40 to 85 C for all packages. BLOCK DIAGRAM PIN ASSIGNMENT PIN 4 = GND (V-) PIN 8 = VCC (V+) Rev. 01 IL4558 SCHEMATIC DIAGRAM (One Section Only) MAXIMUM RATINGS* Symbol V + - Parameter Supply Voltage Supply Voltage Differential Input Voltage Input Voltage Power Dissipation in Still Air Operation Temperature Ranfe Storage Temperature Range Value 18 -18 30 15 570 -40 to 85 -55 to 125 Unit V V V V mW C C V VIDR VIN PD Ta Tstg * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol V + - Parameter Supply Voltage Supply Voltage Min Max 16 -16 Unit V V V Rev. 01 IL4558 ELECTRICAL CHARACTERISTICS (TA = 25C, V+ = +15 V, V- = -15 V) Symbol VIO IIO IIB ri AV VOM VICR CMRR PSRR SR I ,I SR PC VN Isource Isink + - Parameter Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Large-Signal Voltage Gain Output Voltage Swing Test Conditions RS 10K Guaranteed Limits Min Max 5.0 200 - 500 0.3 Unit mV nA nA M V/mV V V V dB RL 2K, VC = 10V RL 10K RL 2K 20 12 10 12 Input Common-Mode Voltage Range Common Mode Rejection Ratio Supply Voltage Rejection Ratio Slew Rate Supply Current Slew Rate Power Consumption Input Noise Voltage Sourse Current Sink Current RL = 2K RL = RS = 1K f = 30Hz 30KHz RS 10K RS 10K RL 2K 70 150 0.8 1.6 5.6 170 3.5 - 20 20 V/V mA V/s mW Vrms mA mA Transient Response Test Circuit Unused OpAmp Rev. 01 IL4558 TYPICAL PERFORMANCE CURVES VOp-p - RL FREQUENCY f (Hz) VNI - f LOAD RESISTANCE RL (k) VOM - VCC, VEE FREQUENCY f (Hz) SUPPLY VOLTAGE V+, V- (V) VOp-p- f I I - TA FREQUENCY f (Hz) AMBIENT TEMPERATURE TA (C) Rev. 01 IL4558 N SUFFIX PLASTIC DIP (MS - 001BA) A 8 5 B 1 4 Dimension, mm Symbol A B MIN 8.51 6.1 MAX 10.16 7.11 5.33 0.36 1.14 2.54 7.62 0 2.92 7.62 0.2 0.38 10 3.81 8.26 0.36 0.56 1.78 F L C D C -T- SEATING PLANE F G M H J N G D 0.25 (0.010) M T K H J K L M N NOTES: 1. Dimensions "A", "B" do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D SUFFIX SOIC (MS - 012AA) Dimension, mm 5 A 8 Symbol A B P MIN 4.8 3.8 1.35 0.33 0.4 1.27 5.72 0 0.1 0.19 5.8 0.25 MAX 5 4 1.75 0.51 1.27 H B C 1 G 4 C R x 45 D F -TD 0.25 (0.010) M T C M K SEATING PLANE G J F M H J K M P R 8 0.25 0.25 6.2 0.5 NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B 0.25 mm (0.010) per side. Rev. 01 IL4558 SIP-9 Rev. 01 IL4558 SIP-8 Rev. 01 |
Price & Availability of IL4558
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |